BIOS 032 Updates:

• Adds PCI-E 3.0 Support
• Fixes issues related to Turbo Multipliers
• Fixed error where ELEET Ratio Control will cause Windows to hang
• Software will now show the correct PCI-E lane configuration
• Overclocking improvements

• Fixed issue where applying voltage in ELEET caused system shutdown
• Fixed default CPU Multiplier
• Fixed issue where disabling LAN2 disables PCIE devices
• Fixed issue where Numlock would not default on
• Add RTL and IOL options
• Supports PS/2 Mouse
• Adds current memory speed display
• Fixed issue where an OC that failed would not allow Clear CMOS

 

---

Windows Installation

• Download the correct .zip file below for your motherboard:

         132-SE-E775-KR - EVGA X79 SLI
         151-SE-E777-KR - EVGA X79 FTW
         151-SE-E779-KR - EVGA X79 Classified

• First go into your BIOS and load defaults, save and exit
• Close all open programs.
• Go into the folder where you unzipped this package and run the appropriate batch file.
  • For Windows XP, Vista or 7 32Bit: FPTWIN32.BAT
  • For Windows XP, Vista or 7 64Bit: FPTWIN64.BAT
  • If in DOS Mode: FPTDOS.BAT
• Press Y in CAPITAL LETTERS to start the flash process
• DO NOT TURN OFF POWER OR RESET DURING THE FLASH PROCESS
• After the flashing is finished, the system will automatically shut down. Then power on again and go into BIOS, Load Defaults, Save and Exit.

 
USB Flash Drive Installation

• Visit this thread and follow the installation instructions. (Thanks Lvcoyote!).

Warning:
**Do not restart or interrupt your PC while the flash is ongoing
**Do not Flash BIOS on overclocked settings
 

Just installed it, everything went ok.

Bluebrains

Hi Jacob and forum members: I partially build my X79 Classified system today. I installed this BIOS and overclocked my machine to 4.5Ghz. However, the some of the BIOS settings changed after I booted into Windows. For example, the CPU multiplier went  from 45 to 39. Please advise.

 
Is EIST set to enabled or disabled in BIOS? Can you try setting your CPU Power Management settings like below:
 

I make test today ;)
Thanks Jacob !

crash_ice

Computer reboot on stress test at any voltage or setting .....

 
What is your CPU temp?

Hello again Jacob----I am up and running at 4.5GHz at great temps with my Haf-X case. The BIOS page you showed me is different that the BIOS 32 I have. I reloaded BIOS 29, and then reloaded BIOS 32 to make sure I had BIOS 32. Well, because I was getting a red error message with the Windows Installation, my BIOS was  NOT updated. I have EIST set to Disabled. Turbo set to  Enabled. I have  the 6core ratios set to 45. There is no Pkg C  State limit.... listed. No CPU 3R, 6R  and 7R listed. Update . I have updated my to BIOS to 32 by way of the flash drive method.
 
Thanks for your help.

Not stable at 4..5  4.6 i just don t knos what s happen with this board. I RMA the board i just don t know why it s so hard to overclock whit this board.
 
DAMN

testing! looks like it's solve most of my issues with my board!
thank u!

The CPU now always reads 85C in AIDA64 and also eVga Eleet. I fixed 85C reading by enabling the temp readout on the LCD in the bios.

Computer reboot on stress test at any voltage or setting...
Same problem...

i will  try tonight i will let you know if it s work .
Thanks
 

For me no problem with Vdroop enabled or disabled.
It's seems to have problem with PLL override... impossible to boot >4800MHz
 
My post : http://forums.evga.com/tm.aspx?m=1390026
Good work for next bios

badboy64

My G-Skill 16GB  DDR3 2133mhz will not run at 2133 period like it did with the 29 bios and will give me a BSOD if I set it to 2133mhz but will run at 1866mhz. I think I will just stick to the 29 bios for now. It didn't matter what voltages where set at all either.

 
We are having a difficult time reproducing this, what is the exact model/rev of your memory?

silvrhand

EVGA_JacobF

badboy64

My G-Skill 16GB  DDR3 2133mhz will not run at 2133 period like it did with the 29 bios and will give me a BSOD if I set it to 2133mhz but will run at 1866mhz. I think I will just stick to the 29 bios for now. It didn't matter what voltages where set at all either.

We are having a difficult time reproducing this, what is the exact model/rev of your memory?

G.SKILL Ripjaws Z Series 16GB (4 x 4GB) 240-Pin DDR3 SDRAM DDR3 2133 (PC3 17000) Desktop Memory Model F3-17000CL9Q-16GBZH

I would imagine he has the same memory kit that i've had, and all my troubles maybe we are on to something here?  As for the memory it's working currently fine @2133 1.65v on my new board.

I have this G-Skill memory.
http://www.newegg.com/Pro...x?Item=N82E16820231501

BIOS 33 for X79 in final testing now, should release really soon if all goes as planned :) (Twitter Jacob EVGA) :D