I remember I had to replace the intel_xeon32 and 64 files with 0.6.4 and it took my gflops from 56 to 80gflops, but I don't know if that was the newest one, all you can clearly see I made 21 runs and HT is on. If the newest ones were created in march then I couldn't have been on those. Like I said no big deal though, for the overclock I had I should have had higher gflops considering it was a 5.2ghz oc.
This is the run:

Looking at your clock speed vs gflops I have to say you did not have the latest linpack binaries. Sorry, but you need to submit a new stability test screenshot.

I just noticed that the newest version of linpack is 10.3.3. The link from the other day contains files from linpack 10.3.2. They both support gulftown so I doubt there is much of a difference. But just to stay current I have changed the files once again with 10.3.3 and will host LinX 0.6.4 with those files here:
http://www.mediafire.com/?rw6k3vlsa486bja
 
@kram36
If you could change the mediafire link in the OP to this one, that would be great. Just so people download the newest version.

poop I can't go higher on my QPI lol :/

jethc9


I just noticed that the newest version of linpack is 10.3.3. The link from the other day contains files from linpack 10.3.2. They both support gulftown so I doubt there is much of a difference. But just to stay current I have changed the files once again with 10.3.3 and will host LinX 0.6.4 with those files here:
http://www.mediafire.com/?rw6k3vlsa486bja

@kram36
If you could change the mediafire link in the OP to this one, that would be great. Just so people download the newest version.

Done. Thank you!

Arctucas
i7 950 Batch #3008A996
CPU clocked at: 4273 MHz
Voltage: 1.33125V
Idle temps: 34, 30, 34, 30
Load temps: 68, 65, 67, 64
GFlop peak: 55.7585
 

 

Bluebrains
Core i7 980x
CPU Clocked at 4509.8MHz
Voltage: 1.423
Idle temps: 19, 33, 27, 24, 32, 33
Load temps: 84, 83, 78, 75, 86, 82
GFlop peak: 80.2477
 
 
 
 
 
 

Finiousfingers
Core i7 920co
CPU clocked at: 4231.5
Voltage: 1.45 without vdroop
Idle temps: 36-38C
Load temps: 84-88C
GFlop peak: 54.4356
WOOOT

Attachment(s)

Attachments are not available: Download requirements not met

go little antec go...
 

finiousfingers - love your voltage

hmm is that a D0  chip ???

Just a quick question can you use EVGA Precision to monitor insted of CPU-Z

Knightviper


Just a quick question can you use EVGA Precision to monitor insted of CPU-Z

I suppose it would be fine and that you meant ELEET, not Precision, but if I see unusually low gflops for your clock speed or large variances in the gflops I'm going to call shenanigans on the test because ELEET can change clock speeds.
 
CPU-Z is a quick download and install.

not a prob mate will get cpu-z downloaded when i get back from work the day

All Right I am in:
 
Rafale
i7 980X 3032A341 
4.33GHz
@ 1.375V Vdroop disabled
Idle temps 26/16/27/35/33/22
Max Load Temp 76/73/71/75/81/76
84.47 peak Gflop
Room Temperature was 25C when the benchmark was run
 

Damn, nice results Rafale, but I don't get how your room temp can be 25C when some of your CPU cores are falling below 25C Inaccurate core readings I assume?
 
That's some impressive Kuhler performance though, I'll have to admit.

Yeah the core temp readings do not seem to be calibrated the same. I am not sure why. I have had 3 980x and their temp distribution accross different cores were never the same.

Good Job finiousfingers! Glad to see that my old original 920 CO (voltage hog) chip is still going strong. It's a good chip.

 
rexrzer77
 
All data is in the JPEG also:
 
Core i7 920 D0 @4315Mhz - On Air ONLY
Batch#3849B056 - Turbo Boost & HT "ON"
VCore 1.32500V + 125MV VTT
Idle Temps-36,42,40,42
Load Temps-86,90,90,93
 
I used the LinX in the download on Page No.1 of this Stability thread, and did
it all by the book-ie the LinX 0.64 with the new binaries on the 1st page of
this thread. If the GFlops don't look high enough for your purposes you can
fault the LinX on Page No.1 here...not my run.
 
This is my Rig no.3 for FAHome, it's in my signature also. 
 
Have a great day, and low voltage rules!
 
rexrzer77 
 
 

Attachment(s)

Attachments are not available: Download requirements not met

Damn good job rexrzer77! Very impressive on AIR!

Thanks all that helped me get there, I am stil learning and am loving the new challenges of a custom rig.

Get everyone added. Nice job to all! 

Thanks for the Gulftown binaries. I ran a quick 20 passes on my big machine and pulled the following.
Now its time to tweak and get the GFs up some.
980x 29x150 Watercool 3.0 block
12 Gigs Dominator ram 3x4Gb boards watercooled
scvette
Core i7 980x
CPU clocked at: 4.339Ghz
Voltage: 1.341v
Idle temps: 24, 28, 28, 24, 30, 30 
Load temps: 61, 64, 59, 57, 63, 66 
GFlop peak: 79.2205 GFlops peak

Hey Kram,
 
I should be at the top of the Gulftown list. I got the best Gflops.
That's because my RAM is at 1955MHz and I left my my QPI@6.4GT (6.7GT effectively) and my uncore at 2x (=3910MHz)
 
SCvette, 
 
Come on you can do better than that on water... gogogo!

Your GFlops are killer, but the list goes by clock speed. If I round yours up to 4.33Ghz I would also have to round up the other two currently in front of you to 4.34Ghz and they would still be in front of you. GFlops is used to break clock speed ties.

I know, I was just kiddin' 

Eh up i've shut everything down and I cant get the base level for the problem size I'm running 6Gb of corsair Dominator GT Ram on Win 7
Problem size I can get is 23,050
any help on this please

Run msconfig and look at the start up items. Disable the ones not needed and reboot.

Do this off line then cos I dont want to connet to the tinters with out protection

everything shut off like you said and the Higest problem size I can get is 24,768Mb can anyone help on getting me to the 25,000 problem size?