Need a Starting point for Overclocking my 990x on a evga x58 ftw3 want 4.5GHz

Re:Need a Starting point for Overclocking my 990x on a evga x58 ftw3 want 4.5GHz (sgtharry)

Thu, 23 Feb 2012 13:38:46 GMT

Take a little time and fill this out. Then we can help you better.

This Bios Template is for both the X-58 3X SLi and the X-58 Classified motherboards.
This is to be used in troubleshooting and is not a guide to overclocking. Items that are for the X-58 3x only have a single * before tie line. Items that are for the X-58 Classified only have two ** before the line. When using this template please fill out all the RED areas.

Mother Board ( EVGA X58 Classified E-759 )
Drivers ( 1024 )
Bios ( S225 )
CPU ( 975EE ) (with 920's please also add the stepping CO or DO)
CPU Cooler ( Heat Killer 3.0 )
Memory ( Corsair Dominator GT 2000 7 8 7 20 )
PSU ( Silverstone 1500 )
GPU ( GTX295+ X 2 )
Drivers ( 186.18 )
Operating System ( Windows 7 64 Ultimate )

Frequency Control
CPU Clock Ratio ( 31X )
CPU Host Frequency (Mhz) ( 142 )
MCH Strap ( Auto )
CPU Uncore Frequency (Mhz) ( 4156Mhz { 29X } )
CPU Clock Skew ( 0 ps )
Spread Spectrum ( Disabled )
PCIE Frequency (Mhz) ( 101 )

Memory Feature
Memory Speed ( XMP Profile 1 )
Memory Control Setting ( Enabled )
Memory Frequency ( 1866Mhz / 2:14 )
Channel Interleave Setting ( 6 Way )
Rank Interleave Setting ( 4 Way )
Memory Low Gap ( Auto )
tCL Setting ( 7 )
tRCD Setting ( 8 )
tRP Setting ( 7 )
tRAS Setting ( 20 )
tRFC Setting ( 110 )
Command Rate ( 1t )

Voltage Control
EVGA VDroop Control ( Without VDroop )
CPU VCore ( 1.425 )
CPU VTT Voltage ( +350 )
CPU PLL VCore ( 1.350 )
**IOH PLL VCore ( 1.350 )
DIMM Voltage ( 1.65 )
DIMM DQ Vref ( +0mV )
QPI PLL VCore ( 1.425 )
IOH VCore ( Auto )
IOH/ICH I/O Voltage ( Auto )
**BR04 ( NF200) Voltage ( Auto ) (only on E-759)
**VTT PWM Frequency ( 610 KHZ )
**CPU PWM Frequency ( 1333 KHZ )
**CPU Impedance ( Less )
**QPI Signal Compensation ( Middle )
ICH VCore ( Auto )
*PWM Frequency ( Not Used on Classified )

CPU Feature
Intel SpeedStep ( Disabled )
Turbo Mode Function ( Enabled )
CxE Function ( Disabled )
Execute Disable Bit ( Disabled )
Virtualization Technology ( Disabled )
Intel HT Technology ( Enabled )
Active Processor Cores ( All )
QPI Control Settings ( Enabled )
QPI Link Fast Mode ( Enabled )
QPI Frequency Selection ( 6.400 GT/s )
OC Recorvery ( Enabled )

PnP/PCI PCI Express
Maximum Payload Size ( 512 )

Re:Need a Starting point for Overclocking my 990x on a evga x58 ftw3 want 4.5GHz (area51c)

Thu, 23 Feb 2012 13:28:17 GMT

Ok will give it a shot. i will post screen shots off error's and bios here too. if i have more questons

Re:Need a Starting point for Overclocking my 990x on a evga x58 ftw3 want 4.5GHz (JaskarnSidhu)

Thu, 23 Feb 2012 08:29:08 GMT

Just like every overclock you do you have to start from the bottom and work your way up. Set you multi to the lowest one, your dram freq to the lowest one and try to find your highest stable bclck and raise your vtt accordingly.

Re:Need a Starting point for Overclocking my 990x on a evga x58 ftw3 want 4.5GHz (JaskarnSidhu)

Thu, 23 Feb 2012 08:06:29 GMT

I have a 990x aswell but on a different board. From the research I've done on the 990x and from my own tests I've found that they best preform with multiplies of 31, 32, 33, 34, and 35. With water cooling I can OC to 4.6 Ghz @ 1.39v.

Re:Need a Starting point for Overclocking my 990x on a evga x58 ftw3 want 4.5GHz (Xtrem)

Tue, 21 Feb 2012 23:08:22 GMT

Check your temps ALWAYS, but raise vcore a bump and try running it again, if it goes longer before BSODing, then raise it one more.

Re:Need a Starting point for Overclocking my 990x on a evga x58 ftw3 want 4.5GHz (area51c)

Tue, 21 Feb 2012 20:16:18 GMT

With that setting above i BSOD if i try to run prime what now?

Re:Need a Starting point for Overclocking my 990x on a evga x58 ftw3 want 4.5GHz (area51c)

Tue, 21 Feb 2012 20:08:20 GMT

Im in windows now and posted this on my pc. that im overclocking. i will run prime now for a wile.
Intel Core i7 Extreme 990X
Windows 7 Ultimate Edition SP1 (Build 7601)
CPU Arch : 1 CPU - 6 Cores - 12 Threads
CPU PSN : Intel Core i7 CPU X 990 @ 3.47GHz
CPU EXT : MMX, SSE (1, 2, 3, 3S, 4.1, 4.2), EM64T, VT-x, AES
CPUID : 6.C.2 / Extended : 6.2C
CPU Cache : L1 : 6 x 32 / 6 x 32 KB - L2 : 6 x 256 KB
CPU Cache : L3 : 12288 KB
Core : Gulftown (32 nm) / Stepping : B1
Freq : 4245.72 MHz (132.68 * 32)

MB Brand : EVGA
MB Model : X58 SLI FTW3
NB : Intel X58 rev 22
SB : Intel 82801JR (ICH10R) rev 00
GPU1 Type : NVIDIA GeForce GTX 570
GPU1 Clocks : Core 797 MHz / RAM 1950 MHz
GPU2 Type : NVIDIA GeForce GTX 570
GPU2 Clocks : Core 797 MHz / RAM 1950 MHz
DirectX Version : 11.0
RAM : 12288 MB DDR3 Triple Channel
RAM Speed : 530.7 MHz (2:8) @ 9-9-9-24
Slot 1 : 2048MB (10700)
Slot 1 Manufacturer : Corsair
Slot 2 : 2048MB (10700)
Slot 2 Manufacturer : Corsair
Slot 3 : 2048MB (10700)
Slot 3 Manufacturer : Corsair
Slot 4 : 2048MB (10700)
Slot 4 Manufacturer : Corsair
Slot 5 : 2048MB (10700)
Slot 5 Manufacturer : Corsair

Re:Need a Starting point for Overclocking my 990x on a evga x58 ftw3 want 4.5GHz (area51c)

Tue, 21 Feb 2012 19:53:43 GMT

Ok good news i can boot into windows with this setting below.

BSOD system service exeption or freeze on desktop.

cpu clock ratio 32x
Vcore 1.30v rest on auto

what should i rase?

Re:Need a Starting point for Overclocking my 990x on a evga x58 ftw3 want 4.5GHz (area51c)

Tue, 21 Feb 2012 19:20:40 GMT

Ok now when i boot Starting windows comes up with the little colored ball that turn in too the windows logo and it just freezes there.

What due i do? I mean do i rase ur lower some thing in bois

Re:Need a Starting point for Overclocking my 990x on a evga x58 ftw3 want 4.5GHz (area51c)

Tue, 21 Feb 2012 19:16:43 GMT

ok i am on 32x Memory is 1057 / 2:8 i changed 8-8-8-20 to what xms3 say 9-9-9-24 and dimm voltage 1.650v that what corsair says.

Now i set my cpu Clock Ratio to 32x with Vdroop every thing is set auto.
Bios says target 4266Mhz 133x32
Target Memory 1067Mhz.
I will save and try to boot now.

Re:Need a Starting point for Overclocking my 990x on a evga x58 ftw3 want 4.5GHz (XrayMan)

Tue, 21 Feb 2012 19:14:30 GMT

Moving thread to the appropriate section of the forums!

Re:Need a Starting point for Overclocking my 990x on a evga x58 ftw3 want 4.5GHz (loveha)

Tue, 21 Feb 2012 19:09:17 GMT

area51c

Ok i make a starting point. i raise my cpu multi to 30x and evey thing else on auto and ram is on xmp 1 by the way.

Disable XMP, enter your Timings and Voltage manually. Never use the XMP Profile and overclock at the same time.

Re:Need a Starting point for Overclocking my 990x on a evga x58 ftw3 want 4.5GHz (Xtrem)

Tue, 21 Feb 2012 19:06:03 GMT

did you increase vcore?

Re:Need a Starting point for Overclocking my 990x on a evga x58 ftw3 want 4.5GHz (area51c)

Tue, 21 Feb 2012 18:59:01 GMT

Ok i make a starting point. i raise my cpu multi to 30x and evey thing else on auto and ram is on xmp 1 by the way.

Re:Need a Starting point for Overclocking my 990x on a evga x58 ftw3 want 4.5GHz (area51c)

Tue, 21 Feb 2012 18:32:01 GMT

Yes i have read it i got my over clocking over view from that guide.
But it did not help. because i tried from there starting point and no luck.

Re:Need a Starting point for Overclocking my 990x on a evga x58 ftw3 want 4.5GHz (vD_Edition)

Tue, 21 Feb 2012 18:05:39 GMT

http://www.techreaction.n...oomfield-and-gulftown/

Have you read that yet? It's a very good primer.

Re:Need a Starting point for Overclocking my 990x on a evga x58 ftw3 want 4.5GHz (area51c)

Tue, 21 Feb 2012 17:58:25 GMT

Oh sorry about that. I am on air cooling on stock setings cpu under load the in a nice 110.4F. I would be happy with a sold 4.2GHz stable. but i cant even get close. I tryed just trurning up the cpu multi to 29x and evey thing else on stock and i can be stable. but any more than 29x like 30x and all setings on auto it frezzes at windows start up logo. No bsod thu. I have read i should be able to get 4.2 easy on my 990x. but i just cant seam to get stable. i would like to have a starting point so i can boot ok on 4.4 in cpu-z then then if i get error will go from there. and post it so i know what to rase ur lower in bios.

Sorry about typos no atuo correct.
Thank You
Cole AKA AREA 51c

Re:Need a Starting point for Overclocking my 990x on a evga x58 ftw3 want 4.5GHz (vD_Edition)

Tue, 21 Feb 2012 17:44:15 GMT

cooling???

4.5 on gulftown is nothing like 4.5 sandybrigde. It is significant, not easy. (at least not easy to be totally, ie linpack stable)

Re:Need a Starting point for Overclocking my 990x on a evga x58 ftw3 want 4.5GHz (loveha)

Tue, 21 Feb 2012 17:39:44 GMT

Your first post was only an Hour ago...............................

Re:Need a Starting point for Overclocking my 990x on a evga x58 ftw3 want 4.5GHz (area51c)

Tue, 21 Feb 2012 17:36:55 GMT

Any one?

Re:Need a Starting point for Overclocking my 990x on a evga x58 ftw3 want 4.5GHz (area51c)

Tue, 21 Feb 2012 17:07:07 GMT

all i want is 4.5Ghz Stable. Witch should be easy with my 990x and my evga ftw3 and ram is XMS3 DDR3 1600 All dimms full so 6x2 12gb total. and 2 gtx 570s stock and 64gb ssd.

Re:Need a Starting point for Overclocking my 990x on a evga x58 ftw3 want 4.5GHz (area51c)

Tue, 21 Feb 2012 17:04:57 GMT

I am trying it agin now.

Re:Need a Starting point for Overclocking my 990x on a evga x58 ftw3 want 4.5GHz (area51c)

Tue, 21 Feb 2012 17:04:26 GMT

I did as the guide said even know i using a 990x and folloed it to the letter and i clocked save a it rebooted and screen where blank and evga board display said 69 then 00 then e8 so i cleared cmos and will try it again with less vcore i think.

Boot after i flood guide i boot to black screen no post nothing so i had to clear cmos and start from scratch.

Re:Need a Starting point for Overclocking my 990x on a evga x58 ftw3 want 4.5GHz (randolla)

Tue, 21 Feb 2012 16:31:39 GMT

Try here

http://www.evga.com/forums/tm.aspx?m=20028&high=

Need a Starting point for Overclocking my 990x on a evga x58 ftw3 want 4.5GHz (area51c)

Tue, 21 Feb 2012 16:29:28 GMT

Hello I just got my system built and i been try for a day now to get a stable overclock of 4.5Ghz will settle for 4.4ghz but i just can't same to be stable any where but on stock on my new 990x. When i got it i try just changing the Clock ratio to 32x any even thing else on auto and system will but a freeze on windows 7 booting logo and no BSOD. So i started over and i try different things like raising voltages and such but no luck. I get a bsod after a stress test most of time on at 4.2ghz even bout boots fine.

I really need a starting port on with to start with like adjust cpu clock ratio or cpu host freqs or or uncore or what? Guides have not helped me much that i have goggled.

Once i get a starting point i can post errors and Bsod screens hot and stuff but i have not even been able to get of 3.8ghz stable.

So Please Help
Thank You
AREA 51c